Maytag bravos xl washer making grinding noise when agitating

5. Washer Won't Spin Fast Enough. Laundry overload, faulty lid, poor drainage, loose or defective drive belt, loose belts, or faulty water level switch. Reduce the excess load, replace the faulty lid lock, unclog the drains, replace the defective drive belt, tighten loose bolts or change the water level switch. 6.

Maytag bravos xl washer making grinding noise when agitating. Hi. Our washer's been working fine for sometime when just today, and I had a small load in the washer, it made this clunking/grind sound while washing. I checked and let it agitate for a bit when I heard the same sound again. I stopped the washer but am not sure what's going on. Is it finally kicking the bucket or is there still hope for it?

Maytag washers may make loud noises when there is a defect in the tub bearing or motor coupling, a worn-out drive pulley, damaged clutch assembly, or a clogged drain pump. Additionally, washers often make a squealing or whining noise when they’ve been overloaded. If your washer has been making any of the noises described above, you’ve come ...

Unplug the washer from the electrical outlet. Locate the shift actuator, which is typically located on the bottom of the washer near the motor. Disconnect the wiring harness from the shift actuator. Remove the mounting screws that secure the shift actuator to the gearbox. Detach the shift actuator from the gearbox.Trouble with a maytag bravos top load washer. I replaced the Splutch kit, and now, after sensing, when it tries to - Answered by a verified Appliance Technician ... Maytag Bravos XL MVWB980BW0 makes a clunking noise when agitating. Spin is quiet. ... It is making a grinding noise while agitating (with no clothes in the washer). ...Maytag Washing Machine Model MVWC565FW2. Some common Maytag front-load washer problems include not agitating or spinning, and not draining or filling with water. Perhaps your washing machine is vibrating during spin cycles or making noises during wash cycles. Don't stand for this kind of appliance misbehavior.When it comes to doing laundry, having a reliable and efficient washing machine is essential. One popular option on the market is the Maytag Bravos XL washer. Known for its large c...Hi. Our washer's been working fine for sometime when just today, and I had a small load in the washer, it made this clunking/grind sound while washing. I checked and let it agitate for a bit when I heard the same sound again. I stopped the washer but am not sure what's going on. Is it finally kicking the bucket or is there still hope for it?This is usually caused by a worn out bearing or a worn out agitator. To determine which part is causing the noise, you will need to open up the washer and inspect the parts. If the bearing is worn out, it will need to be replaced. If the agitator is worn out, it will need to be replaced as well. Maytag Washer Makes Grinding Noise When Agitating ...

That is what started the original issue of the agitator not separating from the drum. I was able to reseat the actuator and all was good for 2 weeks until this noise happened. I have replaced the actuator in an attempt to resolve this noise and have so far been unsuccessful. All the cam/clutch pieces are clean and free of cracks/breaks/slippage ...Maytag Bravos XL MVWB980BW0 makes a clunking noise when agitating. Spin is quiet. ... MAytag Atlantis MAV7650 AWW Agitator makes a loud noise during agitation cycle. ... My Whirlpool Quiet wash Imperial Series washer was making a grinding noise when it should be agitating.BEST-RATED WASHING MACHINES FROM MAYTAG® Find the best washer for your laundry needs. LEARN MORE. ... Bravos XL® HE Top Load Washer with PowerWash® System. MVWB850YW. Manuals & Documentation. Need Product Help? Chat or Call 1-800-344-1274 Hours of Operation:Mon–Fri: 8AM–6PM | Closed on weekends.1. Laundry Overload. Your Maytag washer shouldn’t hold more than ¾ its capacity. If it does, the chances are that the washer won’t spin, and if it does, then it’ll become noisy, sometimes sounding like a jet engine. Also, note that an overload could be why your Maytag washer won’t spin dry clothes.I have a maytag bravo xl. I'm trying to remove the bolt holding the agitator bolt. Unlike others, when I try to - Answered by a verified Appliance Technician ... Maytag Bravos MCT makes a grinding noise when agitating. Spins fine in spin cycle. ... I have a 2 year old Maytag Bravos XL washer and a coin has fallen down between the washer floor ...My maytag Bravo XL washing machine has gotten really loud when it is in the spin cycle and spinning. Maybe 3 years - Answered by a verified Appliance Technician ... So unfortunately the only thing that makes a roaring noise during the spin cycle on this washer is a bad bearing seal and shaft. This is quite a project to replace these parts but ...

Maytag MVWB850YW0 Bravos XL Washer - Loud Grinding Agitator Noise but Splines Look OK? Video & Pics Included. ... Maytag Washer MVWB850YW0 Bravos XL Suspension Rods? bassadict69; Jul 16, 2022; Maytag/Magic Chef/Admiral/Jenn-Air ... please consider making a donation. R.I.P. Jake (Edward John Lucier) Forums. Appliance Repair Talk. Washers. Maytag ...1. Washer Not Moving to the Next Cycle. One common problem you may encounter is your Maytag Bravos XL washer not moving to the next cycle. This can be frustrating, but it’s …My brand new Maytag Bravos washer is making a grinding sound - is this normal? ... my maytag bravos xl top load washer is not empyting the fabric softener and is not extracting all of the water out of the load ... Maytag Bravos MCT makes a grinding noise when agitating. Spins fine in spin cycle.06 - Shock Absorber. Many front-load washer tubs use shock absorbers to dampen tub movement during operation. If one of the shock absorbers becomes dislodged or breaks, the tub may begin shaking and hitting the sides of the washer cabinet, making a loud noise when the appliance is in the wash or spin cycle. It is recommended to replace all of ...If you have a Maytag Dryer similar to the one we have in this video that is making a noise, its important you immediately try to address and fix it before so...Our Maytag washing machine is making a loud screeching sound when in certain points if the wash cycle - I believe - Answered by a verified Appliance Technician ... I went through the diagnosis steps for a MAYTAG Bravos XL MVWB850YG0 washing machine and the first time it completed all 1 thru 9 steps and then just shut off. ... MY …

Wa state hunting forum.

My 2 year top loader Maytag started making loud noises during agitating. It doesn't do it all the time but it's not right. It started making this noise a we... It takes 1-2 hours to fix on average. The instructions below from DIYers like you make the repair simple and easy. Many parts also have a video showing step-by-step how to fix the "Noisy" problem for Maytag MVWB725BW0. So, if your MVWB725BW0 washer grinding noise, loud noise or scraping noise, the following info will help you identify the problem.1. Load Distribution. If you put in clothes in your Maytag washer and run the spin cycle and it starts making grinding noises then the most common reason we believe can be the uneven distribution of the load. So, don't rush, wait and check if you have accidentally put all the clothes on a single side. If this is the issue then evenly ...Maytag Bravos XL MVWB980BW0 makes a clunking noise when agitating. Spin is quiet. ... Maytag Bravos MCT makes a grinding noise when agitating. Spins fine in spin cycle. What is causing the noise? ... I have a 2 year old Maytag Bravos XL washer and a coin has fallen down between the washer floor and the agitator. The washer may be overloaded. When the washer is overloaded, the balance system may be under pressure. This could cause different types of noises, such as squeaks or squeals. Always follow the loading instructions in your Owner's Manual. Refer videos shown below for “Leveling the washer” or “Out of Balance”. Leveling the Washer. Sep 19, 2558 BE ... ... Maytag Bravos HE washing machine. It was having issues and making a loud grinding noise during agitation for a while, and then finally just ...

Washer It seems like it only makes the grinding noise while it's agitating. On a 3 year old machine that could be a couple of things. One is this pulley is loose. It is under the machine behind a plastic guard. The other is model dependant, some have a plastic hub under the wash plate/agitator.Lg Wave Force washer is making grinding and squealing noises when agitating. Top loading. Approx 8-9 years old. ... Maytag bravos xl top load making loud noise as. MVW8835DW4. ... My GE Profile top load washer is making grinding noise like a screw or obstruction is stuck somewhere beneath in the motor/ trans.Hello. i have a maytag model #PAV2300AAW. When agitating my washer makes a loud grinding noise. it kind of sounds like plastic on metal so i replaced the base agitator. That did not fix the problem. i … read moreIf your Maytag washer is making loud or noisy sounds, especially when it's filling with water, the water inlet valve could be the culprit. As time passes, mineral deposits can accumulate inside the valve, leading to a restriction in water flow. This restriction can result in noise during the fill cycle.KEY TAKEAWAYS. Your Maytag washer could be making a grinding noise due to overloading or unbalanced loads, worn-out tub bearings, drive pulley issues, stator assembly malfunction, or a loose washer basket or drum. To prevent this, avoid overloading the washer, ensure it’s properly leveled, and maintain regular cleaning.5. Washer Won’t Spin Fast Enough. Laundry overload, faulty lid, poor drainage, loose or defective drive belt, loose belts, or faulty water level switch. Reduce the excess load, replace the faulty lid lock, unclog the drains, replace the defective drive belt, tighten loose bolts or change the water level switch. 6.How to fix a Maytag/Whirlpool/Amana/Kenmore washer that is making a loud grinding noise during the wash/agitate cycle. Learn how to replace the clutch/splutc...The instructions below from DIYers like you make the repair simple and easy. Many parts also have a video showing step-by-step how to fix the "Noisy" problem for Maytag MVWX655DW1. So, if your MVWX655DW1 washer grinding noise, loud noise or scraping noise, the following info will help you identify the problem. Parts for Maytag MVWX655DW1My Bravos washing machine makes a loud grinding noise on agitation. I watched some YouTube videos that connected the sound to the plastic gear assembly wearing down. It could be bearings too.

Grinding or Rubbing Noises: This new style washer makes many different noises. Typically, a grinding or rubbing noise will only occur in the cycle's agitation/wash or spin portions. The drive system on these units is different than previous washers. You may hear the motor sound as the motor alternates directions or hear some gear sounds.

I have a Maytag Bravos washing machine that makes grinding sounds when agitating and spinning. It appears that the tub drops down several inches too depending on the size of the load, so I thought it was rubbing on the bottom. I just replaced all 4 springs but it didn’t help. I also replaced the agitator about a month ago and it was …When adjutating making rubbing, slipping noise. Bravos xl mct. Approx 7 years old. Just starting due to moving - Answered by a verified Appliance Technician ... I have a Maytag Bravo XL MCT washer; ... The drum will rotate by hand but won't cycle normally, it makes a grinding or rubbing noise ...My Bravos washing machine makes a loud grinding noise on agitation. I watched some YouTube videos that connected the sound to the plastic gear assembly wearing down. ... I have a Maytag Bravos XL washer I purchased 1 1/2 years ago. It has worked well, however, recently it has begun squealing right at the beginning of the load cycle as it is ...Another issue you may face is finding excess lint and hair on your clothes after washing them in the Maytag Bravos XL washer. This can be caused by a clogged drain pump filter or using too much detergent. Clean the filter regularly and ensure you’re using the appropriate amount of detergent for your load size. 3.I have a Maytag Centennial Commercial Technology top loader and it is making a grinding noise when agitating. It seems to spin fine so I thought the clutch was ok. I replaced the agitating dogs, mainly because they were cheap and I was hoping it might fix it. I also took the gear case out and tested it and it didn't sound as if it was the problem.Wellbutrin XL (Oral) received an overall rating of 8 out of 10 stars from 15 reviews. See what others have said about Wellbutrin XL (Oral), including the effectiveness, ease of use...I have a maytag performa pav2300 washer. when the machinhe start to agitate it makes a loud growling/ grinding noise. Agitater moves and seems to lock in place fine it will spin and drain fine. Althou …6. Check the drive shaft: Inspect the drive shaft for signs of wear and tear. If it is worn, replace it. 7. Check the pulley: Inspect the pulley for signs of wear and tear. If it is worn, replace it. In conclusion, the whirlpool washing machine squeaking noise when agitating is most likely caused by a worn out agitator bearing.

Gold rush cast pay per episode.

Exit 61 lie.

Maytag Washer Rattling or Banging Sound. Refer to the video below for an example of the fill hoses rattling against the washing machine: Maytag washer MVWB855DC3 agitator spins instead of drum and has a grinding noise to it. ... Maytag Bravos XL MVWB835DW0 ... Maytag Bravos MCT makes a grinding noise when agitating. Spins fine in spin cycle. What is causing the noise? ...We have a bravos xl dryer that has started squeezing at the beginning of the drying cycle. ... it was making some noise at the beginning of the cycle, but then stopped making the noise. Now it doesnt make the noise, but no heat. ... I have a Maytag Bravos MCT washer that makes a squeaking noise when agitating. ...A common cause of noise during agitation in washing machines is a loose or worn agitator. Over time, the agitator can become loose due to the constant back-and-forth movement during each washing cycle. This can result in rattling, clunking, or banging noises that are often more pronounced during the agitate cycle.Here's how to fix the pump: Step 1. Unplug the washing machine from the electrical supply. Step 2. Unplug the front panel, plug the washer back in and give it a run (without touching the appliance with your hands to avoid an electric shock). Step 3. Verify if there's any agitation noise without the pump.Maytag Washer mav6200aww. Agitator makes grinding noise and clothes very wet after spin. You can turn agitator one way but it will not turn back to the right. Tried new agitator piece - didn't help. L … read moreAnother issue you may face is finding excess lint and hair on your clothes after washing them in the Maytag Bravos XL washer. This can be caused by a clogged drain pump filter or using too much detergent. Clean the filter regularly and ensure you're using the appropriate amount of detergent for your load size. 3.The drum bearing supports the back of the Maytag dryer drum. It can wear out over time. If it's worn, the Maytag dryer may make noise. To check, remove the belt and try turning the drum by hand. If the drum spins easily, the bearing is likely ok. But if the drum makes squeaking or grinding noises and is hard to turn, the bearing could be bad.To turn tones on and off: Hold the Audio button for 3 seconds to turn off all sounds. Lights will still function, but tones will not. This is normal. Hold the Audio button for 3 seconds again to return to tones. See your Owner's Manual for more information regarding setting the tones on the washer.You can get your clothes clean and go green with this high-efficiency Bravos X washer. The ENERGY STAR qualified Maytag Bravos X washer features low water wash with EcoConserve, which uses 70 percent less water and energy. It boasts superb cleaning power, and with eight automatic cycles and three temperature settings you'll have plenty of options to provide the best care for your clothes.Here is why a Maytag dishwasher will make a grinding noise and how to fix it. As a general rule, do an Affresh cycle to clear any blockages caused by food. But, if the grinding noise persists it's because an internal component has failed mechanically. In general, have a repair technician inspect what component is causing it, and repair or ...Maytag hav2360aww makes grinding noise while agitating but spins fine - Answered by a verified Appliance Technician ... Maytag Bravos XL MVWB835DW0 ... I have a maytag performa pav2300 washer. when the machinhe start to agitate it makes a loud growling/ grinding noise. Agitater moves and seems to lock in place fine it will spin and drain fine. ….

May 24, 2023. 8:00 am. Is Your Maytag Washer Making Noise? This May Be Why. Nothing surpasses the convenience of today’s washing machines, especially those from leading brands like Maytag. However, as with any …Rattling noise in your Maytag dryer may be due to loose components, blower wheel issues, or foreign objects. To address these issues, first, unplug the dryer and remove the access panel. Inspect and tighten any loose screws, nuts, or fasteners, and check the blower wheel for damage or secure attachment. Additionally, examine the area around the ...The name "Maytag" along with the words "Powerwash Agitator" are included in capital letters on the top of the washing machine's agitator. The name "Maytag" is also included on the front control panel with a range of buttons and the control knob. The washer includes a top glass door that lets users wash while the cycle runs.In that case, the coins, pins, buttons, bra wires, and more can also get stuck between the main agitator and the inner tub or below the tub. This can cause the washer to go off balance. So, what you can do is simply try removing these things by pulling on them gently after unplugging the washer from the electric socket. 5.Maytag Centennial washer making grinding noise on agitate & spin and doesn't function Just replaced splutch and - Answered by a verified Appliance Technician ... I have a maytag Bravos washer mvwx655dw1. would not spin dry. Replaced the transmission. Worked fine but making a grinding sound during agitation. Call you people and sent another one.The Maytag Bravos XL washer is a popular choice among homeowners due to its large capacity and advanced features. However, like any appliance, it is not without its flaws. One comm...Maytag hav2360aww makes grinding noise while agitating but spins fine - Answered by a verified Appliance Technician ... Maytag Bravos XL MVWB835DW0 ... I have a maytag performa pav2300 washer. when the machinhe start to agitate it makes a loud growling/ grinding noise. Agitater moves and seems to lock in place fine it will spin and drain fine.Should you find your Maytag washer making loud, banging noises during the spin cycle, one potential cause could be a loose washer basket or drum. This can be particularly common in older washers where the shock absorbers or drum bearings have worn out, causing the basket or drum to become off-balance. Verify that the basket or drum is properly ... Maytag bravos xl washer making grinding noise when agitating, Below are the 13 probable causes why your Maytag Bravos washer won't spin: 1. Power Problem. Sometimes, your washer won't spin the clothes if the washer doesn't even start. One reason why it won't start is due to a lack of power. Start by confirming if your washer is plugged into the wall socket and if it's on., When it comes to doing laundry, having a reliable and efficient washing machine is essential. One popular option on the market is the Maytag Bravos XL washer. Known for its large c..., Maytag Performa Model: PAVT244AWW Serial: 22898082EV I have a Maytag washing machine that suddenly stopped working. It may have been overloaded to cause the problem but I am not sure. When the machine went to start the agitate cycle this loud noise in the video started and a burning smell came from the machine., If you experience a burning rubber smell from your washer, you should inspect the pump belt. How to tell if the pump belt in a washing machine needs replacing: Disconnect your washer from the power source and open your washer's cabinet. Locate and remove the pump belt in order to inspect it. It will be attached to the drive motor pulley, and ..., 5. Washer Won’t Spin Fast Enough. Laundry overload, faulty lid, poor drainage, loose or defective drive belt, loose belts, or faulty water level switch. Reduce the excess load, replace the faulty lid lock, unclog the drains, replace the defective drive belt, tighten loose bolts or change the water level switch. 6., Maytag Bravos XL washing machine makes a loud noise when spinning. Sounds like a bad bearing. I removed the back - Answered by a verified Appliance Technician ... It's making a terrible grinding noise. Its a Maytag bravo. ... I have a maytag Bravo XL washer and for several months now it has had a very loud spin cycle. We can't have a ..., I have a Maytag Bravos washer that is making a grinding noise and not properly spinning the wash plate - Answered by a verified Appliance Technician ... Maytag Bravos XL MVWB980BW0 makes a clunking noise when agitating. Spin is quiet. ... I have a Maytag bravos washer MVWB835DW4 that isn't agitating properly. It moves the …, Learn how to fix a GE top load washing machine that is making a grinding noise. The model in the video is a GTW220ACK4WW but this video applies to a lot of t..., Maytag bravo washer, making a clicking sound only during agitating, 5 years, model mvwx700xw1, not sure, no - Answered by a verified Appliance Technician ... Maytag Bravos XL MVWB980BW0 makes a clunking noise when agitating. Spin is quiet. ... Model MVWX655DWO Serial CS3144709 When it is in the wash cycle it makes a loud pop noise when it is ..., 10. Check the lid switch for any signs of damage or wear. In conclusion, the Whirlpool Cabrio washer grinding noise when agitating is most likely caused by a worn out agitator, a damaged drive belt, or a faulty motor. If the washer is still under warranty, it is best to contact the manufacturer for a repair or replacement., You may also hear a humming/whirling noise during the spin portion of the cycle as the motor winds up to turn the washer basket at a higher speed. The pump will run continuously throughout the drain cycle. You may hear a humming sound from the pump, this may be more noticeable once the majority of the water has been drained., Mar 7, 2020 · I have a maytag performa pav2300 washer. when the machinhe start to agitate it makes a loud growling/ grinding noise. Agitater moves and seems to lock in place fine it will spin and drain fine. Althou … , The TomTom One XL GPS device can connect to Bluetooth compatible mobile phones, which enables you to make hands-free calls through the GPS device and receive updated information fo..., The Maytag Bravos XL Dryer has a sanitizing cycle which uses high temperatures. This cycle helps to kill 99.9% of household bacteria. This will keep clothes clean. It is also a better option for towels, bedding, and stuffed animals. Extra Power Button. The Maytag Bravos XL Dryer has an extra Power button which enhances the drying process., Model MVWX655DW1 Doesn't fully agitate. My washer is no longer agitating fully and is not getting my clothes clean. It will go through the rinse and spin cycles properly, though it seems to fill the tub up almost completely…which I don't remember it always doing. Makes a louder than usual clicking noise when on the …, Below are the 13 probable causes why your Maytag Bravos washer won't spin: 1. Power Problem. Sometimes, your washer won't spin the clothes if the washer doesn't even start. One reason why it won't start is due to a lack of power. Start by confirming if your washer is plugged into the wall socket and if it's on., 1. Load Distribution. If you put in clothes in your Maytag washer and run the spin cycle and it starts making grinding noises then the most common reason we believe can be the uneven distribution of the load. So, don’t rush, wait and check if you have accidentally put all the clothes on a single side. If this is the issue then evenly ..., 24K views 7 years ago. Can anyone diagnose what is going on with the Washing Machine? Makes this loud grinding noise during agitation. ...more., Maytag washers may make loud noises when there is a defect in the tub bearing or motor coupling, a worn-out drive pulley, damaged clutch assembly, or a clogged drain pump. Additionally, washers often make a squealing or whining noise when they've been overloaded. If your washer has been making any of the noises described above, you've come ..., I have a maytag Washer (bravo) Model MVWX655DWO Serial. I have a maytag Washer (bravo) Model MVWX655DWO Serial CS3144709 When it is in the wash cycle it makes a loud pop noise when it is agitating POP POP POP POP on each agitation works fine it just wakes ... Maytag Performa PAV2300AWW Washer makes grinding noise when agitating., Maytag Bravos XL washing machine makes a loud noise when spinning. Sounds like a bad bearing. I removed the back - Answered by a verified Appliance Technician ... It's making a terrible grinding noise. Its a Maytag bravo. ... I have a maytag Bravo XL washer and for several months now it has had a very loud spin cycle. We can't have a ..., You may also hear a humming/whirling noise during the spin portion of the cycle as the motor winds up to turn the washer basket at a higher speed. The pump will run continuously throughout the drain cycle. You may hear a humming sound from the pump, this may be more noticeable once the majority of the water has been drained., Maytag wahsher making slow, clicking noise during agitation and water filling. Top loader. 5 years old. Just - Answered by a verified Appliance Technician ... I have a Maytag Bravos washer, I believe it's the 655 model. ... I have a performer washer that has a burning smell when it starts agitating and makes a bunch of noise and ratcheting ..., Maytag Atlantis washing machine makes grinding noise when agitating. Everything else seems to work fine- spin, - Answered by a verified Appliance Technician. ... Hello again, Trouble with a maytag bravos top load washer. I replaced the Splutch kit, and now, after sensing, when it tries to agitate it makes a loud grinding noise. ..., Maytag Atlantis washing machine makes grinding noise when agitating. Everything else seems to work fine- spin, drain, etc. ... Brand new Maytag washer making grinding noise during fill cycle ... Degree. 6,756 satisfied customers. Trouble with a maytag bravos top load washer. I replaced the. Hello again, Trouble with a maytag …, Below is a table summary of 11 reasons your Maytag washing machine won't spin (plus their respective fixes). Probable Cause. Fix. 1. Wrong washer setting. Select the right spin/wash setting. 2. Poor drainage. Remove the source of the drain blockage., Here’s how you can fix a Maytag washer that makes noise and won’t start: Unplug the washing machine. Open the control panel situated at the top of the machine. Disconnect the wire from the lid lock button from the control panel. Now, have a screwdriver and disassemble the upper cover where the lid lock switch is., Common problems with Maytag Bravos washers include failure to start, water filling slowly, water leakage, failure of the door or lid to lock and overflowing. Other problems include..., I have a maytag performa pav2300 washer. when the machinhe start to agitate it makes a loud growling/ grinding noise. Agitater moves and seems to lock in place fine it will spin and drain fine. Althou …, Maytag Performa Model: PAVT244AWW Serial: 22898082EV I have a Maytag washing machine that suddenly stopped working. It may have been overloaded to cause the problem but I am not sure. When the machine went to start the agitate cycle this loud noise in the video started and a burning smell came from the machine., So, when a washer starts making an unusual noise, that’s a clear sign that something isn’t right. Front-load and top-load washers will have different reasons for making grinding, humming, or squealing noises. Grinding is generally a sign that a part has worn out. Humming, on the other hand, is caused by something getting stuck or …, Today, my Kenmore 110.92596100 washing machine started making a loud metallic clicking/ratcheting noise when agitating. There are no abnormal noises during filling or spinning, just during agitation. The agitator dogs were replaced a few months ago, for the first time since new (about 25 years) and appear to still be operating as they should., Your Maytag Bravos washer is stuck on sensing because of a jammed keypad, incorrect setting, faulty shift actuator or control board, or a short-circuited lid lock. If that's not it, it could be a defective inlet valve, sensor fault, wiring issue, faulty timer, drain blockage, or low water pressure. So, there are at least 11 possible ...